BS EN 6055 pdf free download

BS EN 6055 pdf free download. Aerospace series – Rod-end with bearing EN 4265 in corrosion resisting steel, external threaded shank – Dimensions and loads – Inch series.
2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2133, Aerospace series 一Cadmium plating of steels with specified tensile strength 1450 MPa, copper, copper alloys and nickel alloys EN 2424, Aerospace series一Marking of aerospace products EN 4265, Aerospace series一Bearing spherical plain, metal to metal in corrosion resisting steel一Wide series一Dimensions and loads一Inch series EN 6099, Aerospace series一Rod-ends with plain bearing, metal to metal一Technical Specification ISO 1132-1, Rolling bearings一Tolerances 一Part 1: Terms and definitions ISO 3161, Aerospace一UN] threads一General requirements and limit dimensions ISO 3353-1, Aerospace一Lead and runout threads一Part 1: Rolled external threads ISO 3353-2, Aerospace一Lead and runout threads一Part 2: Internal threads ISO 8074, Aerospace一Surface treatment of austenitic stainless steel parts MIL-PRF-23827, Grease, aircraft and instrument, gear and actuator screw, NATO Code No.G-354 metric1 MIL- PRF-46010, Lubricant, solid film, heat cured, corrosion inhibiting, NATO Code-S-17381 MIL-PRF-81322, Grease, aircraft, general purpose, wide temperature range, NATO Code-G-3951 NAS 559, Lock-rod end (key type)2 SAE AMS 5643, Steel, corrosion resistant, bars wire, forgings, tubing and rings 16Cr-4.0Ni-0.30(Cb+ Ta)-4.0Cu solution heat treated, precipitation hardenable2 TR 4475, Bearings and mechanical transmissions for airframe applications一Vocabulary3 3 Terms, definitions and symbols For the purposes of this document, the terms and definitions given in TR 4475 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: 一ISO Online browsing platform: available at http://www.iso.org/obp 一IEC Electropedia: available at http://www .electropedia.org/ Symbols of limit deviations are in accordance with definitions of ISO 1132-1. ar maximum angle of tilt of the outer ring with respect to the inner ring, with the spherical surface of the outer ring being completely in contact with the inner ring; C permissible static radial load; Admp single plane mean bore diameter deviation; Ads deviation of a single bore diameter; cp push out load; Gq fatigue load, 4 Requirements 4.1 Configuration, dimensions, tolerances and mass Configuration, dimensions, tolerances and mass shall be according to Figure 1 and Table 1. Table 1 and Table 5: Dimensions and tolerances are expressed in millimetres (inches). Figure 1: Dimensions and tolerances for Ra max. are expressed in um (uin). Values apply after surface treatment. 4.2 Surface roughness Surface roughness shall be according to Figure 1. Surface roughness is measured before surface treatment.
4.5 Material Inner ring: see product standard EN 4265. Outer ring: see product standard EN 4265. Rod-end body: see AMS 5643, hardness 35≤HRC≤42. 4.6 Surface treatment Surface treatment as defined in chapter 5 (designation) with following codes:一rod-end body: 一code T: passivated according to ISO 8074; 一code P: cadmiurm plating and chromating according to EN 2133，10μm to 20 um (400 uin to 800 uin);一exception: threads, 5 um to 15 um (200 pin to 600 uin); 一  bearing: see EN 4265.6 Marking Marking shall be according to EN 2424, style A. 7 Technical specification Technical specification shall be according to EN 6099. 8 Quality management systems The manufacturer’s operations shall be an approved production organisation for aerospace products and shall demonstrate that it has implemented and is able to maintain a quality management system (e.g according to EN 9100 or an equivalent aerospace accepted and established quality management system]. The qualification procedure for aerospace standard products [e.g. according to EN 9133 or an equivalent aerospace accepted and established qualification procedure) shall be used and documented according to the specified tests if not otherwise agreed between customer and supplier.BS EN 6055  pdf download.